我国彩票中奖十大记录

S-5-PV Kit Solar Attachment Solutions

我国彩票中奖十大记录The concept of combining PV arrays with standing seam metal roofing is growing—for good reasons. Metal roofs have a life expectancy of more than 40 years. Shouldn’t the mounting system last as long? With S-5! zero-penetration attachment technology and PV Kit 2.0, the solarized metal roof is the most sustainable system available –and without compromising roof warranties! PV Kit 2.0 is the also the best solution for attaching PV modules directly to any exposed fastener metal roof.

S-5! now introduces a new and improved PV Kit, boasting lower installation time and cost for PV flush-mounting. The kit comes preassembled with MidGrab or EdgeGrab for easier and more efficient installation. A single tool drives the top bolt, eliminating several installation steps. The PV Kit 2.0 features more aggressive bonding teeth for better grounding. Fewer lugs/ground wires required.

New from the metal roof experts: The S-5 PV Kit 2.0 is designed to save you time and money —

EdgeGrab

MidGrab

PV Kit Features:

  • Preassembled components save time and money
  • Versatile:  same kit for most module thicknesses
  • Only one tool needed for installation
  • Installs with module, reducing lay-out time
  • All non-corrosive aluminum and stainless steel
  • Single-piece EdgeGrab installs with ease
  • Added slots for wire tie-off
  • Low profile hardware provides flush, clean finish
  • Available in black by special order
  • 1″ gap between modules, allowing load reduction per ASCE-7
  • UL 2703 Listed

Solar Panel Mounting

(Left) Without the S-5-PV Direct Attachment Solutions, lugs or copper wires are required to bond PV panels within a string of modules.

我国彩票中奖十大记录(Right) Using the S-5-PV Direct Attachment Solutions, wires and lugs are no longer needed from module-to-module, but will still be needed to bond strings together and to ground the system.

Note: The drawings above show an example of continual conductivity; please refer to the engineer for specific job layouts.

The PV Kit 2.0 is furnished with the hardware is shown below, (Attachment clamp or bracket supplied separately.) PV Kit 2.0 is compatible with most common metal roofing materials, including aluminum, steel, copper, zinc and stainless.

我国彩票中奖十大记录The Module Placement Bevel Guide makes the module placement easier. The mounting disk is multi-directional and rails are not required. The PV grab ears are broader for ease of installation and secure module engagement.

PV Kit fits a wide array of module thicknesses. Use with S-5! mini clamps enables fitting to all standing seam metal roof profiles of any material. When paired with other S-5! products, the PV Kit 2.0 also works on all trapezoidal ribbed and corrugated metal roofs.

我国彩票中奖十大记录The MidGrab can also be used as an edge condition if desired.

我国彩票中奖十大记录Modules can be easily installed from ridge-down or eave-up.

我国彩票中奖十大记录More slots for wire securement.

我国彩票中奖十大记录Flush finish with module surface.

Parts

Tools Needed

  • Screw Gun
  • 3/16” Hex Bit Tip (provided)
  • Calibrated Dial Torque Wrench

 


Installation & Help



Suggestions for Spacing of S-5! Clamps for PV Assemblies

The following suggestions assume that determination has been made that the roof to which the S-5! clamps will be attached is structurally adequate. Any loads imposed on the S-5! clamps will be transferred to the panels. Panel seams must have sufficient flexural strength to carry these loads. Panels must also be adequately attached to the building structure, and the structure must be sufficient to carry these loads. The makers of S-5! clamps make no representations with respect to these variables. It is the responsibility of the user to verify this information, or seek assistance from a qualified design professional, if necessary.

The key to frequency and spacing of attachment points for PV is to distribute loads to the metal standing seam panels in a manner that is consistent with the intended distribution of loads from the roof panels into the building structure. With very few exceptions, the attachment of a single S-5! clamp (even the “Mini”) to the seam will be stronger than a single point of attachment of the seam to the building structure. Hence the “weak link” is not the S-5! clamp, but the attachment clips that hold the metal panels to the building structure, or the beam strength of the roof panel seam itself.

我国彩票中奖十大记录The most conservative approach to the spacing/frequency of PV attachment to the roof is to determine the spacing/frequency of the roof’s attachment to the building structure, then duplicate it at minimum. Determining panel attachment spacing in one axis is very simple: Standing seam panels’ attachment will be made using concealed hold-down clips within the seam area of the panel. So, in that axis, the clip spacing is the same as the seam spacing. The location of the clips along the seam (in the other axis) can be determined by a) consultation with the roof system manufacturer or installer, b) checking from the underside or, c) close examination from the topside along the seam. There will usually be a slight, but detectable, deformation of the seam at the clip location visible from the roof’s topside. Many standing seam roofing systems are installed on “pre-engineered steel” buildings. The attachment spacing in that industry is typically 5′-0″ and is readily apparent by inspecting the structural purlins to which the panel clips are attached from the roof underside (interior of the building).

If the panel clips are spaced, for instance, 5′-0″ on center along the seam, then use the 5′-0″ dimension as a maximum spacing for the S-5! clamps. (S-5! clamps may also be spaced at closer centers, but not wider.) When modules are direct attached (without racking) in the landscape orientation, this spacing dimension is dictated by the smallest dimension of the PV frame. Using the roof panel clip spacing as a maximum spacing template for S-5! clamps is a sound practice, whether the PV modules are attached direct to S-5!, or to a racking system, which is in turn attached to the S-5! (and panel seams). To evenly distribute loads, it is also necessary that each seam be involved in the finished assembly. Thus, every time a seam is traversed, it should be attached. Such an attachment scheme should evenly distribute wind loads into the building structure through the panels and their attachment, as was intended in the original roof construction assembly.

Note: Wind dynamics are complex, and S-5! advises review by a qualified licensed professional who understands wind effects and metal roof design and construction.

ijb67qa.cn is a direct distributor of S-5 parts and components. View our complete line of DIY solar kits that include S-5 attachments.

我国彩票中奖十大记录 We're experienced solar veterans, providing custom solar solutions since 2006. Our work has been featured on CBS, Price is Right, and USA Today. Choose us for a boutique, complete service experience - we help you every step of the way until you're generating free energy from the sun.


Call (866) 798-4435 for Expert Help

我国彩票中奖十大记录Questions? Contact one of our expert solar reps. We can answer technical questions, provide financing, and help you choose the right parts for your solar system.


We respect your privacy and your information will not be shared with anyone.

手机版彩票过滤工具 怎么购买手机赌博软件 手机棋牌输了几百万 快乐棋牌游戏 怎么样进入赌单双软件 我爱彩票邀请码是多少 快钱彩票官网 手机版集结号捕鱼游戏 我想查查彩票开奖结果 怎么下载波克棋牌